Fiberplex

Fiberplex

  • Fiberplex SFP Modules

    The FiberPlex Technologies line of SFP Modules supports a host of data rates, wavelengths and power configurations providing maximum flexibility. The SFPs simultaneously support various SONET,  Synchronous Digital Hierarchy (SDH) and IEEE Ethernet standards. Both dual fiber transceivers and single fiber Bi-Directional (BiDi) round out the flexible offering. The selection table in the Data SFP datasheet lists many of the popular  options and the corresponding FiberPlex SFP part number.  If you do not see exactly what you are looking for, contact your FiberPlex Technologies representative.

    The FiberPlex Technologies line of SFP Modules supports a host of data rates, wavelengths and power configurations providing maximum flexibility. The SFPs simultaneously support various SONET,  Synchronous Digital Hierarchy (SDH)…
    Quick View
  • Fiberplex TD-1280 | TD-1281 Fully Compatible TIA-232 / 7 Channel RX/TX Pair

    The TD-1280 and TD-1281 pair together to form a powerful balanced serial data transport solution. The DB-25 connectors are pinned out to directly support a TIA-232 serial link. However due to the transparency and flexibility of the design, the TD-1280/81 can be used as 3×2 independent 1 Mbps TIA-232 channels and 5×5 independent 120 Kbps TIA-232 channels.

    This incredible versatility can solve a myriad of serial data communications problems. Your once limited serial links can not only be consolidated but extended to over 20 Km on a single fiber pair. SCADA (supervisory control and data acquisition), Telecommunications, Facility Automation and Control can all benefit from the TD-1280/81.

    For more advanced systems, a ‘Regeneration’ switch on the TD-1281 allows users to toggle between synchronous applications that require Send Timing (ST) and asynchronous or synchronous applications that require Terminal Timing (TT).

    The TD-1280 and TD-1281 pair together to form a powerful balanced serial data transport solution. The DB-25 connectors are pinned out to directly support a TIA-232 serial link. However due…
    Quick View
  • Fiberplex TD-1580 | TD-1581 Fully Compatible EIA-530 / 6X4 RS-422 Serial Interface With 1×2 RS-232

    The TD-1580 and TD-1581 pair together to form a powerful balanced serial data transport solution. The DB-25 connectors are pinned out to directly support an EIA-530 serial link. However due to the transparency and flexibility of the design, the TD-1580/81 can be used as 6×4 independent 6 Mbps RS-422 channels and 2×1 independent 256 Kbps RS-232 channels (see below for details). This incredible versatility can solve a myriad of serial data communications problems. Your once limited serial links can not only be consolidated but extended to over 20 Km on a single fiber pair. SCADA (supervisory control and data acquisition), Telecommunications, Facility Automation and Control, even DMX Lighting control applications can all benefit from the TD-1580/81. For more advanced systems, a ‘Regeneration’ switch on the TD-1581 allows users to toggle between synchronous applications that require Send Timing (ST) and asynchronous or synchronous applications that require Terminal Timing (TT).

    The TD-1580 and TD-1581 pair together to form a powerful balanced serial data transport solution. The DB-25 connectors are pinned out to directly support an EIA-530 serial link. However due…
    Quick View
  • Fiberplex TTM 6 Position Truss Mount Solution For TD Series Modules With 16 Channel Modular Panel

    Another compliment to the incredible flexibility of the FiberPlex ‘TD Series’ of fiber optic modules, the TTM provides connection, mounting, power, and cable management for up to 6 front facing TD modules in a rugged aluminium truss mountable package. This system also functions very well as a convenient, portable “lunchbox” solution. Each of the 16 channels of the modular TTM rear panel can accommodate any Neutrik™ D Series connector, LC and ST barrel connectors, DB 9 connectors, etc. The unused positions are simply fitted with a blank panel. In addition, 4 front Aux positions can be fitted with multiple connector options providing a true in-line mounting system. The integrated key-hole mounting holes on the bottom of the TD units lock securely on mating studs while a rear retention bar holds them securely in place. A 6 position power wiring harness and included AC power supply provides, not just 9 VDC power, but a positive earth ground to the modules via a positive locking Neutrik™ powerCON TRUE1 connector.  Managing all of that cabling and fiber can sometimes be quite a chore, the TTM allows a simple solution to put maximum capacity and flexibility into a single 1U space.

    Another compliment to the incredible flexibility of the FiberPlex ‘TD Series’ of fiber optic modules, the TTM provides connection, mounting, power, and cable management for up to 6 front facing…
    Quick View
  • Fiberplex TDR-01-AC 6 Position Rear Connect Powered Rack For TD Series Modules

    Complementing the flexibility of the FiberPlex ‘TD Series’ of fiber optic modules, the TDR-01-AC provides mounting, power and cable management for up to 6 modules in a compact and rugged aluminum 1U rack. With the TD modules rear facing, connections to the TD units are made from the rear, inside of the rack enclosure. The integrated key-hole mounting holes on the bottom the TD units lock securely on mating studs while a rear retention bar holds them securely in place. A 6 position wiring harness and included power adapter provide, not just 9 VDC power, but a positive earth ground to the modules via 3 position Phoenix™ locking power connectors.  Managing all that cabling and fiber can sometimes be quite a chore so an extended cabling tray with integrated tie down points are provided to help make your installation clean.

    Complementing the flexibility of the FiberPlex ‘TD Series’ of fiber optic modules, the TDR-01-AC provides mounting, power and cable management for up to 6 modules in a compact and rugged…
    Quick View
  • Fiberplex TDP 6 Position Front Connect Rack For TD Series Modules With 16 Channel Modular Front Panel

    Complementing the flexibility of the FiberPlex ‘TD Series’ of fiber optic modules, the TDP provides front of rack connection, mounting, power, and cable management for up to 6 front facing TD modules in a compact and rugged aluminium 1U rack. Each of the 16 channels of the modular TDP front panel can accommodate any Neutrik™ D Series connector, LC and ST barrel connectors, DB9 connectors, etc. The unused positions are simply fitted with a blank panel. The integrated key-hole mounting holes on the bottom of the TD units lock securely on mating studs while a rear retention bar holds them securely in place. A 6 position power wiring harness and included power adaptor provide, not just 9 VDC power, but a positive earth ground to the modules via 3 position Phoenix™ locking power connectors.  Managing all that cabling and fiber can sometimes be quite a chore, the TDP allows a simple solution to put maximum capacity and flexibility into a single 1U space.

    Complementing the flexibility of the FiberPlex ‘TD Series’ of fiber optic modules, the TDP provides front of rack connection, mounting, power, and cable management for up to 6 front facing…
    Quick View
  • Fiberplex TD-DINR DIN Rail Mounting Bracket For TD Series Modules

    Complementing the flexibility of the FiberPlex ‘TD Series’ of fiber optic modules, the TDR-DINR provides a versatile DIN rail mounting solution. The integrated keyhole mounting holes on the bottom the TD units lock securely on mating studs while a non-marring nylon retention screw holds them securely in place. TD modules can be edge mounted for more rail space or flat mounted for more vertical space by simply moving the rail clips to the secondary position using only a screwdriver.

    Complementing the flexibility of the FiberPlex ‘TD Series’ of fiber optic modules, the TDR-DINR provides a versatile DIN rail mounting solution. The integrated keyhole mounting holes on the bottom the…
    Quick View
  • Fiberplex TIS-8632 6 Port 10/100/1000 Ethernet Switch – 4 Copper Ports With 2 SFP Optical Ports

    Elegantly simple yet packed with an advanced feature set, the FiberPlex Technologies TIS-8632 is a powerful 6 Port 10/100/1000 Ethernet Switch. The unit features (4) RJ-45 UTP ports as well as (2) flexible SFP ports. The TIS-8632 is part of the FiberPlex TD Import Series. Two or more TIS-8632 can be chained together via fiber to provide a distributed solution where isolation, distance, security and/or noise immunity is needed between nodes. Locally, an 8 copper x 2 optical switch can be created using a Passive SFP Cable Assembly between SFP ports. This cable saves cost by replacing (2) optical modules and a fiber cable with an inexpensive copper jumper. While this solution is only good for very short ‘jumper’ lengths, it provides flexibility for local port expansion.

    Elegantly simple yet packed with an advanced feature set, the FiberPlex Technologies TIS-8632 is a powerful 6 Port 10/100/1000 Ethernet Switch. The unit features (4) RJ-45 UTP ports as well…
    Quick View
  • Fiberplex FOI-7282/TD-7282 2-Wire Audio Transceiver With Serial Data And Control (E&M 2-Wire)

    The FiberPlex Technologies TD-7282 is an innovative fiber conversion unit which allows for the creation of point-to-point or daisy chained connections utilizing your current inventory of 2-wire party-line intercom systems such as RTS and ClearCom. The unit converts 2-wire duplex analogue audio to fiber for long or short haul transport. In addition to the audio, a multi-format serial data connection and a bidirectional pair of contact closures are included. The combination of audio and signalling also provides a seamless solution for 2-wire E&M applications.

    As part of the FiberPlex 7200 series of converters, the TD-7282 is optically compatible with other units in the series. For example, the TD-7282 can be paired with a TD-7280 to create a 2-wire to 4-wire conversion over fiber.

    The FiberPlex Technologies TD-7282 is an innovative fiber conversion unit which allows for the creation of point-to-point or daisy chained connections utilizing your current inventory of 2-wire party-line intercom systems such…
    Quick View
  • Fiberplex FOI-6012/TD-6012 12.5Gbps Flexible Interface SFP/SFP+ Dual Transceiver Workbox

    The true “Swiss Army Knife” of fiber optic transport, the TD-6012 in conjunction with any combination of a myriad of FiberPlex or third party dual transmit or dual receive SFP/SFP+ (Small Form-Factor Pluggable) optical & electrical modules, allows you to transport what you want, when you want it, how you want it, wherever you want it; all over one product solution… The FiberPlex TD-6012 and SFP/ SFP+ modules should be in everyone’s toolbox.

    The true “Swiss Army Knife” of fiber optic transport, the TD-6012 in conjunction with any combination of a myriad of FiberPlex or third party dual transmit or dual receive SFP/SFP+…
    Quick View
  • Fiberplex SAC-1-AC Single Stand Alone Chassis For FOM Series

    The FiberPlex SAC‐1‐AC is a standalone FOM card chassis, providing power, enclosure and secure mounting for a single Fiber Optic Module. Each SAC‐1‐AC may be rack, wall or desktop mounted utilising the included components of the SAC‐1 Mounting System.

    The FiberPlex SAC‐1‐AC is a standalone FOM card chassis, providing power, enclosure and secure mounting for a single Fiber Optic Module. Each SAC‐1‐AC may be rack, wall or desktop mounted…
    Quick View
  • Fiberplex RMC-5000 Chassis For FOM Series, 16 Card

    The RMC-5000 rack mount chassis provides up to sixteen available slots for any FOM series fiber optic module card. The FOM cards are typically installed from the rear of the chassis, providing electrical and fiber optic connections at the rear of the chassis. A front panel window allows viewing of status leds on each installed card indicating power supply status, fiber optic link status, signal line status, and control or configuration information, depending on the particular card. The chassis backplane allows various support modules to be installed, allowing for future expansion and control options. No active components are an integral part of the chassis backplane, providing high reliability and minimal maintenance issues.

    The RMC-5000 rack mount chassis provides up to sixteen available slots for any FOM series fiber optic module card. The FOM cards are typically installed from the rear of the…
    Quick View
  • Fiberplex PSM-5000 Power Supply For RMC-5000

    The PSM-5000 power supply module is designed to be inserted into the RMC- 5000 rack mount chassis. The module provides an operating voltage through the chassis backplane to power up to sixteen fiber optic module cards. Each rack mount chassis is shipped with one power supply module.

    For additional reliabilty and security, a second PSM-5000 may also be added for power redundancy. If the first PSM-5000 fails, the second PSM-5000 will take over the entire load and carry on normally. Additionally, if one PSM fails, an onboard alarm will sound. An PWR LED indicates that the +24VDC output voltage is present, and that the module is operating properly.

    The PSM-5000 power supply module is designed to be inserted into the RMC- 5000 rack mount chassis. The module provides an operating voltage through the chassis backplane to power up…
    Quick View
  • Fiberplex FOM-8220 10/100 Ethernet Fiber Converter, 2 Channel

    The FOM-8220 provides complete electrical isolation for 2 independent channels of both 10BASE-T and 100BASE-TX Ethernet communications. The card incorporates an automatic MDI/MDIX switch over capability that allow users to use either a straight or crossover cable for all LAN configurations.

    The card can be used in areas of high electrical noise or in and out of RF shielded enclosures. The fiber optic cable is not susceptible to interference caused by impulse noise, crosstalk, or EMI. Privacy of communications is also enhanced because the fiber optic cable does not radiate any emissions.

     

    The FOM-8220 provides complete electrical isolation for 2 independent channels of both 10BASE-T and 100BASE-TX Ethernet communications. The card incorporates an automatic MDI/MDIX switch over capability that allow users to…
    Quick View
  • Fiberplex FOM-8020 10/100 Ethernet Fiber Conveter

    The FOM-8020 provides complete electrical isolation for both 10BASE-T and 100BASE-TX Ethernet communications. The card incorporates an automatic MDI/MDIX switch over capability that allow users to use either a straight or crossover cable for all LAN configurations.

    The card can be used in areas of high electrical noise or in and out of RF shielded enclosures. The fiber optic cable is not susceptible to interference caused by impulse noise, crosstalk, or EMI. Privacy of communications is also enhanced because the fiber optic cable does not radiate any emissions.

    The FOM-8020 provides complete electrical isolation for both 10BASE-T and 100BASE-TX Ethernet communications. The card incorporates an automatic MDI/MDIX switch over capability that allow users to use either a straight…
    Quick View
  • Fiberplex FOM-5600 ISDN Fiber MUX, 4 Channel

    The FOM-5600 provides complete electrical isolation for 4-wire S/T-Interface ISDN communications. The unit has four channels that are independent of each other with two switches each that allow users to select between different ISDN modes and interfaces.

    The unit can be used in areas of high electrical noise or in and out of RF shielded enclosures. The fiber optic cable is not susceptible to interference caused by impulse noise, crosstalk, or EMI. The potential problem of creating ground loops or ground offsets is also eliminated because signal ground is not carried over the fiber. The unit enhances privacy of communications because fiber can not be tapped without being detected and does not radiate any emissions. In addition, the FOM-5600 offers much longer transmission distances than traditional Cat5 cabling. Each channel can be retimed to allow longer S/T runs. A typical link consists of two FOM-5600, one at each end of the network with a duplex fiber optic cable between them.

    The FOM-5600 provides complete electrical isolation for 4-wire S/T-Interface ISDN communications. The unit has four channels that are independent of each other with two switches each that allow users to…
    Quick View
  • Fiberplex FOM-3941 | FOM-3942 Nortel (Avaya) Meridian M2000 And M3000 Series (FOM), 4 Channel

    The FOM-3941 and FOM-3942 both provide complete electrical isolation for Nortel’s Meridian™ M2000 and M3000 series digital telephones. The FOM-3941 connects to the digital line card and automatically senses and corrects any improper polarity reversals on the RJ-11. The bidirectional signaling between the digital line card and telephone is then carried across a duplex fiber optic cable. The FOM-3942 reproduces the digital signaling at the isolated end of the fiber optic link and provides power sufficient to operate M2000 and M3000 series digital telephones.

    The FOM-3941 and FOM-3942 both provide complete electrical isolation for Nortel’s Meridian™ M2000 and M3000 series digital telephones. The FOM-3941 connects to the digital line card and automatically senses and…
    Quick View
  • Fiberplex FOM-3841 | FOM-3842 POTS (Plain Old Telephone Service) Fiber Converter, 4 Channel

    The FOM-3841 and FOM-3842 provide complete electrical isolation for four independent channels of 2-wire telephone communications. The FOM-3842 supports standard analog phones, STU-III (secure telephone unit) phones, STE (secure telephone equipment) phones, fax machines, and modems and supports Caller ID.

    The units can be used in areas of high electrical noise or in and out of RF shielded enclosures. The fiber optic cable is not susceptible to interference caused by impulse noise, crosstalk, or EMI. Privacy of communications is also enhanced because the fiber optic cable does not radiate any emissions. In addition, fiber optic cable offers much longer transmission distances than traditional telephone line cord wiring. Multimode optics on the units can extend the distance to 2km, while singlemode optics can further extend the distance to 20km. A typical link consists of an FOM-3841 connected to the POTS line and an FOM-3842 at the subscriber’s phone with a duplex fiber optic cable between them.

    The FOM-3841 and FOM-3842 provide complete electrical isolation for four independent channels of 2-wire telephone communications. The FOM-3842 supports standard analog phones, STU-III (secure telephone unit) phones, STE (secure telephone…
    Quick View
  • Fiberplex FOM-1090 | FOM-1091 Multi-Standard Serial Interface, 25 Mbps

    The FOM-1090 and FOM-1091 fiber optic isolator/modem cards provides for full synchronous, asynchronous, or isochronous interfacing to serial data communications equipment. The unit is transparent to all data formats and protocol, and supports timing from the DCE and DTE as well as uncommon clocking styles such as gapped clock or gated clocks that stop in different states to indicate status. The status and direction of all supported signals is shown on front panel indicators in addition to power supply and optical link status for each card.

    The FOM-1090 and FOM-1091 fiber optic isolator/modem cards provides for full synchronous, asynchronous, or isochronous interfacing to serial data communications equipment. The unit is transparent to all data formats and…
    Quick View
  • Fiberplex FOI-6010/TD-6010 12.5Gbps Flexible Interface SFP/SFP+ Transceiver Workbox

    The true “Swiss Army Knife” of fiber optic transport, the FOI-6010 in conjunction with any combination of a myriad of FiberPlex or third party SFP/SFP+ (Small Form- Factor Pluggable) optical & electrical modules, allows you to transport what you want, when you want it, how you want it, wherever you want it; all over one product solution… The FiberPlex FOI-6010 and SFP/ SFP+ module should be in everyone’s toolbox.

    The true “Swiss Army Knife” of fiber optic transport, the FOI-6010 in conjunction with any combination of a myriad of FiberPlex or third party SFP/SFP+ (Small Form- Factor Pluggable) optical…
    Quick View
  • Fiberplex FOI-5401/TD-5401 T1/E1 Fiber Converter

    The FOI-5401 and TD-5401 provide complete electrical isolation for T1, DS1 or E1 communications.

    The unit can be used in areas of high electrical noise or in and out of RF shielded enclosures. The fiber optic cable is not susceptible to interference caused by impulse noise, crosstalk, or EMI. Privacy of communications is also enhanced because the fiber optic cable does not radiate any emissions. FiberPlex recommends “R” units for high security applications because the units have added filtering and shielding for RFI suppression.

    The FOI-5401 and TD-5401 provide complete electrical isolation for T1, DS1 or E1 communications. The unit can be used in areas of high electrical noise or in and out of…
    Quick View
  • Fiberplex FOI-4605 ISDN Fiber Converter

    The FOI-4605 provides complete electrical isolation for 4-wire S/T-Interface ISDN communications.

    The unit can be used in areas of high electrical noise or in and out of RF shielded enclosures. The fiber optic cable is not susceptible to interference caused by impulse noise, crosstalk, or EMI. Privacy of communications is also enhanced because the fiber optic cable does not radiate any emissions. FiberPlex recommends “R” units for high security applications because the units have added filtering and shielding for RFI suppression.

    A typical link consists of two FOI-4605, one at the network terminal and another at the terminal equipment with a duplex fiber optic cable between them.

    The FOI-4605 provides complete electrical isolation for 4-wire S/T-Interface ISDN communications. The unit can be used in areas of high electrical noise or in and out of RF shielded enclosures.…
    Quick View
  • Fiberplex FOI-4451 | FOI-4541 Serial Converter EIA-530/RS-422, 6 Mbps

    The FOI-4451 and FOI-4541 both provide complete electrical isolation for RS- 422 communications. The units are transparent to all handshaking protocols and can accept data and clock signals up to a maximum rate of 6.144 Mbps. A regeneration switch on the FOI-4451 allows users to toggle between synchronous applications that require Send Timing (ST) and asynchronous or synchronous applications that require Terminal Timing (TT). They support tail circuit and null modem functions for DCE to DCE or DTE to DTE communications. This requires two of the same FOI units. An alternate interface (V.35 or RS-232) may be installed at the opposite end, allowing the user to create a link between two electrically incompatible interfaces without requiring a separate interface converter.

    The FOI-4451 and FOI-4541 both provide complete electrical isolation for RS- 422 communications. The units are transparent to all handshaking protocols and can accept data and clock signals up to…
    Quick View
  • Fiberplex FOI-4341 | FOI-4431 Serial Converter V.35, 6Mbps

    The FOI-4341 and FOI-4431 both provide complete electrical isolation for V.35 communications. The units are transparent to all handshaking protocols and can accept data and clock signals up to a maximum rate of 6.144 Mbps. A regeneration switch on the FOI-4341 allows users to toggle between synchronous applications that require Send Timing (ST) and asynchronous or synchronous applications that require Terminal Timing (TT). They support tail circuit and null modem functions for DCE to DCE or DTE to DTE communications. This requires two of the same FOI units. An alternate interface (RS-232 or RS-422) may be installed at the opposite end, allowing the user to create a link between two electrically incompatible interfaces without requiring a separate interface converter.

    The FOI-4341 and FOI-4431 both provide complete electrical isolation for V.35 communications. The units are transparent to all handshaking protocols and can accept data and clock signals up to a…
    Quick View
  • Fiberplex FOI-4141 | FOI-4411 Serial Converter RS-232, 1Mbps

    The FOI-4141 and FOI-4411 both provide complete electrical isolation for RS-232 communications. The units are transparent to all handshaking protocols and can accept data and clock signals up to a maximum rate of 1 Mbps. A regeneration switch on the FOI-4141 allows users to toggle between synchronous applications that require Send Timing (ST) and asynchronous or synchronous applications that require Terminal Timing (TT).They support tail circuit and null modem functions for DCE to DCE or DTE to DTE communications. This requires two of the same FOI units. An alternate interface (V.35 or RS-422) may be installed at the opposite end, allowing the user to create a link between two electrically incompatible interfaces without requiring a separate interface converter.

    The FOI-4141 and FOI-4411 both provide complete electrical isolation for RS-232 communications. The units are transparent to all handshaking protocols and can accept data and clock signals up to a…
    Quick View
  • Fiberplex FOI-4110 10/100 Ethernet

    The FOI-4110 fiber optic isolator uses 820nm optics as a low cost solution for 10BASE-T to 10BASE-FL and 100BASE-TX to 100BASE-SX Ethernet communications. The 820nm optics also provide backward compatibility with legacy devices that have a 10BASE-FL interface.

    The units will have an automatic MDI/MDIX switch over capability that allow users to use either a straight or crossover cable for all LAN configurations. This eases the installation process for simple plug and play. A typical link consists of two FOI-4110, one at each end of the network, with a duplex fiber optic cable between them.

    The units can be used in areas of high electrical noise or in and out of RF shielded enclosures. The fiber optic cable is not susceptible to interference caused by impulse noise, crosstalk, or EMI. FiberPlex recommends “R” units for high security applications because they have added filtering and shielding for RFI suppression.

    The FOI-4110 fiber optic isolator uses 820nm optics as a low cost solution for 10BASE-T to 10BASE-FL and 100BASE-TX to 100BASE-SX Ethernet communications. The 820nm optics also provide backward compatibility…
    Quick View
  • Fiberplex FOI-7280/TD-7280 Line Level Stereo Audio Transceiver With Serial Data And Controls (E&M)

    Elegantly simple yet packed with an advanced feature set, the FiberPlex Technologies, FOI-7280 is a powerful problem solver when it comes to routing audio or transporting E&M signals. The unit converts line level, stereo analogue audio to fiber for long or short haul transport. In addition to the audio, a multi-format serial data connection and a bidirectional pair of contact closures are included. The combination of audio and signalling provides a seamless solution for 4-wire E&M applications.

    Elegantly simple yet packed with an advanced feature set, the FiberPlex Technologies, FOI-7280 is a powerful problem solver when it comes to routing audio or transporting E&M signals. The unit…
    Quick View
  • Fiberplex FOI-2991 | FOI-2992 | FOI-2993 | FOI-2994 Control Signal And Relay Contacts

    The FOI-2991, FOI-2992, FOI-2993, and FOI-2994 all provide complete electrical isolation for control signals and relay closures. The units are uni-directional devices with the FOI-2991 and FOI-2992 having optical transmitters, while the FOI-2993 and FOI-2994 have optical receivers. Both the FOI-2991 and FOI-2992 can accept up to 12 individual control signals. The FOI-2991 can only accept a DC voltage of 0 to +5V, while the FOI-2992 can accept either a DC or AC voltage of +12 to +24V. The FOI-2993 has 12 SPST Form A latching relays and the FOI-2994 has 8 SPDT Form C latching relays.

    The FOI-2991, FOI-2992, FOI-2993, and FOI-2994 all provide complete electrical isolation for control signals and relay closures. The units are uni-directional devices with the FOI-2991 and FOI-2992 having optical transmitters,…
    Quick View
  • Fiberplex FOI-2981 | FOI-4982 | FOI-2983 Audio Line Level 2Ch Plus Doorbell In

    The FOI-2981, FOI-4982, and FOI-2983 all provide complete electrical isolation for audio communications. A typical link consists of either an FOI-2981 or an FOI-2983 at one end of the network transmitting optical signals to an FOI-4982 at the other end of the network with a single fiber optic cable.

    The unit can be used in areas of high electrical noise or in and out of RF shielded enclosures. The fiber optic cable is not susceptible to interference caused by impulse noise, crosstalk, or EMI. Privacy of communications is also enhanced because the fiber optic cable does not radiate any emissions. In addition, fiber optic cable offers much longer transmission distances than copper wiring. Multimode optics on the units can extend the distance to 2km.

    The FOI-2981, FOI-4982, and FOI-2983 all provide complete electrical isolation for audio communications. A typical link consists of either an FOI-2981 or an FOI-2983 at one end of the network…
    Quick View
  • Fiberplex FOI-2971 | FOI-4972 POTS (Plain Old Telephone Service) Fiber Converter

    The FOI-2971 and FOI-4972 provide complete electrical isolation for 2-wire telephone communications. The FOI-4972 supports standard analog phones, STU-III (secure telephone unit) phones, STE (secure telephone equipment) phones, fax machines, and modems and supports Caller ID.

    The units can be used in areas of high electrical noise or in and out of RF shielded enclosures. The fiber optic cable is not susceptible to interference caused by impulse noise, crosstalk, or EMI. Privacy of communications is also enhanced because the fiber optic cable does not radiate any emissions. FiberPlex recommends “R” units for high security applications because the units have added filtering and shielding for RFI suppression.

    In addition, fiber optic cable offers much longer transmission distances than traditional telephone line cord wiring. Multimode optics on the units can extend the distance to 2km, while singlemode optics can further extend the distance to 20km. A typical link consists of an FOI-2971 connected to the POTS line and an FOI-4972 at the subscriber’s phone with a duplex fiber optic cable between them.

    The FOI-2971 and FOI-4972 provide complete electrical isolation for 2-wire telephone communications. The FOI-4972 supports standard analog phones, STU-III (secure telephone unit) phones, STE (secure telephone equipment) phones, fax machines,…
    Quick View
  • Fiberplex RMC-3700 Environmental Enclosure For FOI Modules

    The FiberPlex Technologies RMC-3700 is a heavy duty enclosure designed to survive in indoor and outdoor environments. The chassis is rated to IP54, protecting the internal components from dust and windblown rain. Each chassis provides up to nine (9) available slots for any FiberPlex fiber optic isolator (FOI) or telephone disconnect unit.

    The tenth available slot must be occupied by a power supply module. Each chassis will be shipped with one power supply module (PSM). A second power supply module may also be added for system power redundancy, leaving eight (8) available slots for the installation various combinations of FOI units. If the first power supply module fails, the second will assume the entire system load and carry on normally. The failed power supply module may be hot swapped with a new one without interruption of FOI operation.

    The FiberPlex Technologies RMC-3700 is a heavy duty enclosure designed to survive in indoor and outdoor environments. The chassis is rated to IP54, protecting the internal components from dust and…
    Quick View
  • Fiberplex RMC-3101 Chassis For All FOI Series, 9 Slot 3U

    The RMC-3101 provides up to nine available slots for any fiber optic isolator or telephone disconnect unit. The tenth available slot must be occupied by a PSM-3010 power supply module. Each RMC-3101 will be shipped with one PSM-3010. A second PSM-3010 may also be added for power redundancy, leaving eight available slots for any fiber optic isolator. If the first PSM-3010 fails, the second PSM-3010 will take over the entire load and carry on normally. A cable bay is provided below the module bay for cable routing and enhanced airflow through two rear exhaust fans and a vented front panel.

    The RMC-3101 provides up to nine available slots for any fiber optic isolator or telephone disconnect unit. The tenth available slot must be occupied by a PSM-3010 power supply module.…
    Quick View
  • Fiberplex RMC-2101 Chassis For Size 2 And 4 FOI Modules, 9 Slot 2U

    The RMC-2101 provides up to nine available slots for any size 2 or 4 FOI fiber optic isolator. The tenth available slot must be occupied by a PSM-2010 power supply module. Each RMC-2101 will be shipped with one PSM-2010. A second PSM-2010 may also be added for power redundancy, leaving eight available slots for any fiber optic isolator. If the first PSM-2010 fails, the second PSM-2010 will take over the entire load and carry on normally. A cable bay is provided below the module bay for cable routing and enhanced airflow through two front exhaust fans.

    The RMC-2101 provides up to nine available slots for any size 2 or 4 FOI fiber optic isolator. The tenth available slot must be occupied by a PSM-2010 power supply…
    Quick View
  • Fiberplex PSQ-2920 | PSQ-3920 | PSQ-4920 DC Input Standalone Power For FOI Series

    The PSQ-2920, PSQ-3920 and PSQ-4920 are compact DC power supplies which attach to and the provide operating voltage for FiberPlex’s FOI series isolators. They can power the FiberPlex FOI units with a 12-48 VDC external supply. These DC power supplies are not polarity sensitive, V+ and V- may be reversed for DC inputs. They are equipped with a resettable fuse to protect both the supply and the FOI.

    The PSQ-2920, PSQ-3920 and PSQ-4920 are compact DC power supplies which attach to and the provide operating voltage for FiberPlex’s FOI series isolators. They can power the FiberPlex FOI units…
    Quick View
  • Fiberplex PSQ-2909 | PSQ-3909 | PSQ-4909 Easy Install Standalone Power For FOI Series

    The PSQ-2909, PSQ-3909 and PSQ-4909 are compact AC power supplies which attach to, and provide operating voltage for FiberPlex’s FOI series isolators. The RFI suppressed ‘R’ variant of this power supply has been tested and is recommended for high security or TEMPEST applications. The FiberPlex PSQ supply has been updated to be easier to assemble. Previous versions of the PSQ required a separate bracket and multi-step process to attach the supply to an FOI. This new design you just pop on the back of the FOI and tighten two thumb screws. The all enclosed design will also meet the most stringent safety standards. For more rugged mounting, wall mount adaptors, WMA-2001 and WMA-3002, are available to secure the power supply and fiber optic isolator with screws. Both WMA-2001 and WMA-3002 are compatible with all PSQ and FOI series. The WMA-2001 has an optical patch while the WMA-3002 does not. The wall mount adaptor attaches to either a horizontal or vertical flat surface and provides a convenient termination point which protects both the fiber optic cable and the fiber optic isolator from damage.

    The PSQ-2909, PSQ-3909 and PSQ-4909 are compact AC power supplies which attach to, and provide operating voltage for FiberPlex’s FOI series isolators. The RFI suppressed ‘R’ variant of this power…
    Quick View
  • Fiberplex PSM-3010 | PSM-2010 Power Supply For RMC-3000 Series Chassis

    The PSM-2010 and PSM-3010 are power supply modules designed to be inserted into the RMC-2xxx and RMC-3xxx rack mount chassis, respectively. The modules provide an operating voltage through the chassis backplane to power up to nine fiber optic isolator units. Each rack mount chassis is shipped with one power supply module. For additional reliability and security, a second Power Supply Module (PSM) may also be added for power redundancy. If the first PSM fails, the second PSM will take over the entire load and carry on normally. Additionally, if one PSM fails, an on board alarm will sound. An LED indicates that the +9VDC output voltage is present, and that the module is operating properly.

    The PSM-2010 and PSM-3010 are power supply modules designed to be inserted into the RMC-2xxx and RMC-3xxx rack mount chassis, respectively. The modules provide an operating voltage through the chassis…
    Quick View
  • Fiberplex CMA-2001 / CMA-3002 Chassis Adapter For FOI Series

    The CMA-2001, and CMA-3002 chassis mount adapters are required to securely hold each fiber optic isolator or interface converter installed in a rack mount chassis. Alignment pins on the Chassis Mount Adapter assure proper mating between power connectors on the fiber optic isolators and the rack mount chassis power bus. Easy front or rear access to both the fiber optic and electrical interface connectors when inside the rack mount chassis.

    The CMA-2001, and CMA-3002 chassis mount adapters are required to securely hold each fiber optic isolator or interface converter installed in a rack mount chassis. Alignment pins on the Chassis…
    Quick View
  • Fiberplex WMA-2001 | WMA-3002 Wall Mount Adapters For FOI Series

    The WMA-2001, and WMA-3002 are designed to provide a stable platform for FiberPlex’s fiber optic isolators and interface converters. The wall mount adapter attaches to either a horizontal or vertical flat surface and provides a convenient termination point which protects both the fiber optic cable and the fiber optic isolator from damage.

    The WMA-2001, and WMA-3002 are designed to provide a stable platform for FiberPlex’s fiber optic isolators and interface converters. The wall mount adapter attaches to either a horizontal or vertical…
    Quick View
  • Fiberplex TDU-4000 Telephone Disconnect Unit

    The TDU-4000 provides protection for phones from being used as clandestine listening devices. The unit electrically disconnects the telephone line from the phone when the phone is in the “on hook” position. During disconnect the telephone line is left open, while the voice path on the phone is grounded. This disables room audio from being transmitted onto the telephone line to prevent any eavesdropping. The phone will only connect to the telephone line when it is in the “off hook” position. The “Off Hook” detect and “Ring” detect signals are also opto-isolated from the phone.

    The TDU-4000 provides protection for phones from being used as clandestine listening devices. The unit electrically disconnects the telephone line from the phone when the phone is in the “on…
    Quick View
  • Fiberplex FOI-STS1 STS-1 / OC-1 Fiber Converter

    The FOI-STS1 provides complete electrical isolation for STS-1 SONET communications. In addition, fiber optic cable offers much longer transmission distances than copper wiring. Traditional STS-1 coax cabling is limited to a maximum distance of 1100ft (335m), but multimode optics on the unit can extend the distance to 2km, while singlemode optics can further extend the distance to 20km. A typical link consists of two FOI-STS1, one at each end of the network, with a duplex fiber optic cable between them.

    The FOI-STS1 provides complete electrical isolation for STS-1 SONET communications. In addition, fiber optic cable offers much longer transmission distances than copper wiring. Traditional STS-1 coax cabling is limited to…
    Quick View
  • Fiberplex FOI-DST3 T3 Fiber Converter

    The FOI-DST3 provides complete electrical isolation for T3 or DS3 communications. In addition, fiber optic cable offers much longer transmission distances than copper wiring. Traditional T3 coax cabling is limited to a maximum distance of 1100ft (335m), but multimode optics on the unit can extend the distance to 2km, while singlemode optics can further extend the distance to 20km. A typical link consists of two FOI-DST3, one at each end of the network, with a duplex fiber optic cable between them.

    The FOI-DST3 provides complete electrical isolation for T3 or DS3 communications. In addition, fiber optic cable offers much longer transmission distances than copper wiring. Traditional T3 coax cabling is limited…
    Quick View
  • Fiberplex FOI-DSE3 E3 Fiber Converter

    The FOI-DSE3 provides complete electrical isolation for E3 communications. The unit can be used in areas of high electrical noise or in and out of RF shielded enclosures. The fiber optic cable is not susceptible to interference caused by impulse noise, crosstalk, or EMI. Privacy of communications is also enhanced because the fiber optic cable does not radiate any emissions.

    The FOI-DSE3 provides complete electrical isolation for E3 communications. The unit can be used in areas of high electrical noise or in and out of RF shielded enclosures. The fiber optic…
    Quick View
  • Fiberplex FOI-6012 12.5Gbps Flexible Interface SFP/SFP+ Dual TX/RX Workbox

    The true “Swiss Army Knife” of fiber optic transport, the FOI-6012 in conjunction with any combination of a myriad of FiberPlex or third party dual transmit or dual receive SFP/SFP+ (Small Form-Factor Pluggable) optical & electrical modules, allows you to transport what you want, when you want it, how you want it, wherever you want it; all over one product solution… The FiberPlex FOI-6012 and SFP/ SFP+ modules should be in everyone’s toolbox.

    The true “Swiss Army Knife” of fiber optic transport, the FOI-6012 in conjunction with any combination of a myriad of FiberPlex or third party dual transmit or dual receive SFP/SFP+…
    Quick View
  • Fiberplex FOI-3901 | FOI-3902 Nortel Meridian M2000 And M3000 Series

    The FOI-3901 and FOI-3902 both provide complete electrical isolation for Nortel’s Meridian™ M2000 and M3000 series digital telephones. The FOI- 3901 connects to the digital line card and automatically senses and corrects any improper polarity reversals on the RJ-11. The bidirectional signalling between the digital line card and telephone is then carried across a duplex fiber optic cable. The FOM-3902 reproduces the digital signalling at the isolated end of the fiber optic link and provides power sufficient to operate M2000 and M3000 series digital telephones. The FOI-3902 is compatible with Nortel’s A0367335 plug-in transformer, which provides power to support the additional features on the M2016S digital telephone. A closet power supply can also be used to provide auxiliary power but the power must be inserted between the FOI-3902 and the digital telephone.

    The FOI-3901 and FOI-3902 both provide complete electrical isolation for Nortel’s Meridian™ M2000 and M3000 series digital telephones. The FOI- 3901 connects to the digital line card and automatically senses…
    Quick View
  • Fiberplex FOI-2191 / FOI-2911 Serial Converter RS-232, 128Kbps

    The FOI-2191 and FOI-2911 both provide complete electrical isolation for RS- 232 communications. For compatibility with MIL-STD-188C, the transmit and receive data (TD and RD) can be inverted through either unit by a switch. The units are transparent to all handshaking protocols and can accept data and clock signals up to a maximum rate of 128 kbps. A regeneration switch on the FOI-2191 allows users to toggle between synchronous applications that require Send Timing (ST) and asynchronous or synchronous applications that require Terminal Timing (TT). They support tail circuit and null modem functions for DCE to DCE or DTE to DTE communications. This requires two of the same FOI units. An alternate interface (V.35 or RS-422) may be installed at the opposite end, allowing the user to create a link between two electrically incompatible interfaces without requiring a separate interface converter.

    The FOI-2191 and FOI-2911 both provide complete electrical isolation for RS- 232 communications. For compatibility with MIL-STD-188C, the transmit and receive data (TD and RD) can be inverted through either…
    Quick View
  • Fiberplex FOI-2170 / FOI-2171 / FOI-2172 / FOI-2173 Unidirectional Composite Video with or without Audio

    The FOI-2170 and FOI-2171 both provide complete electrical isolation for composite video communications. The units are compatible with NTSC, PAL, and SECAM video broadcast standards. The units are transparent to all monochrome RS-170, color RS170A, and closed circuit RS-330 video. The FOI-2171 has an AGC (automatic gain control) to stabilise the video output for different fiber optic cable lengths. Adjusting the AGC potentiometer will also increase or decrease the overall scene brightness.

    The FOI-2172 and FOI-2173 both provide complete electrical isolation for composite video and audio communications. The units are compatible with NTSC, PAL, and SECAM video broadcast standards. The units are transparent to all monochrome RS-170, color RS170A, and closed circuit RS-330 video. The FOI-2173 has an AGC (automatic gain control) to stabilize the video output for different fiber optic cable lengths. Adjusting the AGC potentiometer will also increase or decrease the overall scene brightness. The FOI-2172 can accept a wide level of audio input because clipping can be adjusted by the LVL potentiometer, while the FOI-2173 LVL potentiometer controls the volume.

    The FOI-2170 and FOI-2171 both provide complete electrical isolation for composite video communications. The units are compatible with NTSC, PAL, and SECAM video broadcast standards. The units are transparent to…
    Quick View
  • Fiberplex FIS-6510/TIS-6510/FIS-6511/TIS-6511 Wideband RF To Fiber Conversion, Unidirectional With 50Ω SMA

    The TIS-6510 fiber receiver and TIS-6511 fiber transmitter provide a high performance, high reliability, transparent cross-site connection between RF communications equipment. They are ideal for L-Band, low frequency radio and distribution of wireless standards such as cellular, GPS, Wi-Fi and WiMAX. The ultra-wide dynamic range results in negligible degradation of signals due to noise or inter-modulation effects.

    Independent of data format, the 6510/6511 are suitable for most analog or digital signal modulation including FM and QPSK. The RF connects via a 50Ω SMA connector. Units are available with Singlemode LC PC, and ST fiber connections (other custom options available, contact your FiberPlex representative).

    The TIS-6510 fiber receiver and TIS-6511 fiber transmitter provide a high performance, high reliability, transparent cross-site connection between RF communications equipment. They are ideal for L-Band, low frequency radio and…
    Quick View
  • Fiberplex FOI-1GBT 1000 Base-T Ethernet

    The FOI-1GBT provides complete electrical isolation for 1000BASE-T Gigabit Ethernet communications. The unit has an automatic MDI/MDIX switch over capability that allow users to use either a straight or crossover cable for all LAN configurations. The copper interface is fully automatic. If TP+ and TP- are reversed, the unit will automatically swap the polarity internally. Similarly, if the transmit and receive pairs are reversed, the unit will automatically swap both pairs internally. Therefore, either a crossover or straight cable can be used.

    The FOI-1GBT provides complete electrical isolation for 1000BASE-T Gigabit Ethernet communications. The unit has an automatic MDI/MDIX switch over capability that allow users to use either a straight or crossover…
    Quick View
  • Fiberplex FAK-2981 / FAK-2982 Fire Alarm Kit With Strobe

    A complete bundled package for Fire Alarm annunciation applications. Includes warning strobe.

    The unit can be used in areas of high electrical noise or in and out of RF shielded enclosures. The fiber optic cable is not susceptible to interference caused by impulse noise, crosstalk, or EMI. Privacy of communications is also enhanced because the fiber optic cable does not radiate any emissions. In addition, fiber optic cable offers much longer transmission distances than copper wiring. Multimode optics on the units can extend the distance to 2km.

    A complete bundled package for Fire Alarm annunciation applications. Includes warning strobe. The unit can be used in areas of high electrical noise or in and out of RF shielded…
    Quick View
  • Fiberplex ADP-2981 / ADP-2982 Annunciator Speaker

    The ADP-2981 / ADP-2982 is a stand-alone wall or shelf mountable loudspeaker unit. Each unit houses and powers an 8-inch speaker and, in the case of the ADP-2981, a high-intensity strobe.

    The unit utilises FiberPlex FOI series modules to extend Public Address and Mass Notification systems via fiber. External audio signals such as voice announcements, music, a doorbell buzz, etc. are first connected to a FOI-2981 or FOI-2983. This FOI unit then transmits the signal via a fiber optic link to a FOI-4982, conveniently housed and powered by an ADP unit. From there the FOI-4982 drives up to 10 ADP units in a daisy chain.

    The ADP-2981 / ADP-2982 is a stand-alone wall or shelf mountable loudspeaker unit. Each unit houses and powers an 8-inch speaker and, in the case of the ADP-2981, a high-intensity…
    Quick View
  • Fiberplex FOI-2890 Duplex Alarm With Controls

    The FOI-2591 and FOI-2951 both provide complete electrical isolation for RS-422 communications. The units are transparent to all handshaking protocols and can accept data and clock signals up to a maximum rate of 256 kbps. A regeneration switch on the FOI-2591 allows users to toggle between synchronous applications that require Send Timing (ST) and asynchronous or synchronous applications that require Terminal Timing (TT). They support tail circuit and null modem functions for DCE to DCE or DTE to DTE communications. This requires two of the same FOI units. An alternate interface (V.35 or RS-232) may be installed at the opposite end, allowing the user to create a link between two electrically incompatible interfaces without requiring a separate interface converter.

    The FOI-2591 and FOI-2951 both provide complete electrical isolation for RS-422 communications. The units are transparent to all handshaking protocols and can accept data and clock signals up to a…
    Quick View
  • Fiberplex FOI-2591 / FOI-2951 Serial Converter EIA-530/RS-422, 128Kbps

    The FOI-2591 and FOI-2951 both provide complete electrical isolation for RS-422 communications. The units are transparent to all handshaking protocols and can accept data and clock signals up to a maximum rate of 256 kbps. A regeneration switch on the FOI-2591 allows users to toggle between synchronous applications that require Send Timing (ST) and asynchronous or synchronous applications that require Terminal Timing (TT). They support tail circuit and null modem functions for DCE to DCE or DTE to DTE communications. This requires two of the same FOI units. An alternate interface (V.35 or RS-232) may be installed at the opposite end, allowing the user to create a link between two electrically incompatible interfaces without requiring a separate interface converter.

    The FOI-2591 and FOI-2951 both provide complete electrical isolation for RS-422 communications. The units are transparent to all handshaking protocols and can accept data and clock signals up to a…
    Quick View